SMSS 2023 Prelim P3
Uploaded by fish123 · 11 November 2026
Preview
Text from the first pagesThis document consists of 11 printed pages. Shift Laboratory ST. MARGARET’S SCHOOL (SECONDARY) Preliminary Examinations 2023 CANDIDATE NAME CLASS REGISTER NUMBER BIOLOGY Paper 3 Secondary 4 Express Candidates answer on the Question Paper. 6093/03 21 August 2023 1 hour 50 minutes Additional Materials: As listed on the board READ THESE INSTRUCTIONS FIRST Write your name, class and register number on all the work you hand in. Give details of the practical shift and laboratory, where appropriate, in the boxes provided. Write in dark blue or black pen. You may use an HB pencil for any diagrams or graphs. Do not use staples, paper clips, glue or correction fluid. Answer all questions in the spaces provided on the Question Paper. The use of an approved scientific calculator is expected, where appropriate. You may lose marks if you do not show your working or if you do not use appropriate units. At the end of the examination, fasten all your work securely together. The number of marks is given in brackets [ ] at the end of each question or part question. For Examiner’s Use 1 28 2 12 Total 40
2 SMS(S) 2023 You are advised to read the whole question before you start. 1 The enzyme lipase catalyses the digestion of fats into fatty acids and glycerol. You are going to investigate the effect of using lipase of different concentrations on the rate of digestion of fat in milk. In the investigation, an indicator solution will be mixed with milk and lipase solution. Table 1.1 shows the colour of the indicator solution at different pH values. Table 1.1 pH 6 7 8 colour yellow green blue You are provided with: • 12 test-tubes in test tube racks • lipase solution • dilute sodium carbonate solution • milk • deionised water • indicator solution • 250 cm3 beaker • a beaker labelled water bath • styrofoam cup to collect hot water • thermometer • stop-watch • four 5 cm3 syringes • paper towels • marker pen. If sodium carbonate comes into contact with your skin, wash it off immediately. Clean any spillages immediately. You are advised to wear eye protection throughout the investigation. Take care when using hot water.
3 SMS(S) 2023 Read the procedures below and prepare a table to record your results in the space provided in part (b), before beginning your experiment. (a) Complete Table 1.2 by calculating the percentage concentration of lipase solution for test-tube L2. [1] Step 1 Use the marker pen to label six test-tubes L1, L2, L3, L4, L5 and L6. Step 2 Use two 5 cm 3 syringes to make six different concentrations of lipase solutions in the respective test-tubes as shown in Table 1.2. Table 1.2 test-tube volume of lipase / cm3 volume of distilled water / cm3 concentration of lipase solution / % L1 0.0 4.0 0.0 L2 0.5 3.5 L3 1.0 3.0 25 L4 1.5 2.5 37.5 L5 2.0 2.0 50 L6 4.0 0.0 100 Step 3 Use the marker pen to label another six test -tubes M1, M2, M3, M4, M5, and M6. Step 4 Use a plastic pipette to add 2 drops of indicator solution to test-tube M1. Step 5 Use a clean 5 cm 3 syringe to add 1 cm3 of sodium carbonate solution to test-tube M1. Step 6 Use a clean 5 cm 3 syringe to add 2 cm 3 of milk to test-tube M1. Shake to mix. Step 7 Repeat steps 4 to 6 with test-tubes M2, M3, M4, M5 and M6. Step 8 Add about 150 cm3 of tap water to the beaker labelled water bath. Use the styrofoam cup to collect hot water. Mix the hot water and tap water to make a water bath at 45 °C. To prevent your water -bath from overflowing in step 9, do not add more than 200 cm3 of hot water to the water bath. Step 9 Put all 12 test-tubes into the water-bath and leave for five minutes. Ensure that the temperature of the water-bath is maintained at 45 °C. Step 10 After five minutes remove test -tubes M1 and L1 from the water-bath and place them in a test-tube rack. Step 11 Pour the contents of test -tube M1 into test-tube L1. Start a stop -watch. Observe the colour of the contents of test-tube L1.
4 SMS(S) 2023 Step 12 Record the time taken, in seconds , for the blue indicator solution to become yellow. If the blue indicator solution has not become yellow after five minutes, record the time taken as > 300 seconds. Step 13 Repeat steps 10, 11 and 12 for test-tubes M2 and L2, M3 and L3, M4 and L4, M5 and L5, M6 and L6, restarting your stop-watch for each test. Step 14 The rate of fat digestion by lipase can be determined by calculating the reciprocal of the time taken for the blue indicator solution to become yellow. rate of fat digestion = 1000 / t t = time in seconds Calculate the rate of fat digestion for each concentration of lipase solution. If you have recorded a time taken as > 300 seconds, record the rate of fat digestion as zero in your table. Record your results, to the nearest whole number, in the table you have prepared in 1(b). (b) Record your results in a table. [5]
5 SMS(S) 2023 (c) Draw a graph of your results to show the effect of changing lipase concentration on the rate of fat digestion. [4]
6 SMS(S) 2023 (d) (i) State one constant variable in your investigation and explain why it is important to keep this variable constant. constant variable explanation [2] (ii) Describe the results of your investigation as shown in your graph. [2] (iii) Explain how increasing the concentration of lipase causes the change in the time taken for the indicator to turn colour as indicated by your results. [3] (iv) Detergent has a similar function as bile. Suggest and explain the effect if detergent was added into M3 in Step 7. [3]
7 SMS(S) 2023 (e) (i) Suggest two sources of error that apply to this investigation and in each case explain their effect on the quality of the result. source of error explanation source of error explanation [2] (ii) Suggest an improvement to the method, that will reduce the effect of the error, for one of the errors you have identified in 1(e)(i). [1]
8 SMS(S) 2023 (f) Temperature is another factor that affects the rate of enzyme reactions. Outline how you would investigate the effect of temperature on the rate of milk fat digestion by lipase. [5] [Total: 28]
9 SMS(S) 2023 2 The lotus rhizome is consumed as a vegetable in Asian countries. You are provided with a section of a lotus rhizome, labelled R. (a) (i) Make a large drawing of the cut section of the lotus rhizome in the space below. [3] (ii) Measure the maximum diameter of the cut section of the lotus rhizome and record your measurement. Measure the maximum diameter of your drawing of the cut section of the lotus rhizome and record your measurement. [2] (iii) Use the measurements in (ii) to calculate the magnification of your drawing to 2 significant figures. magnification = x [2]
10 SMS(S) 2023 (b) Fig. 2.1 shows a photograph of a lotus plant flower. Fig. 2.1 Draw label lines to the flower in Fig. 2.1 to identify a petal and an anther. [2]
Content continues in the PDF. Download PDF
