2026 RI H3Chem Prelims Questions
Uploaded by Kozak327 · 10 November 2026
Preview
Text from the first pages1 © Raffles Institution 2026 9813/01/S/26 [Turn over RAFFLES INSTITUTION 2026 YEAR 6 PRELIMINARY EXAMINATION Higher 3 CANDIDATE NAME CLASS 2 6 S 0 INDEX NUMBER CHEMISTRY 9813/01 Paper 1 28 September 2026 You must answer on the question paper. 2 hours 30 minutes You will need: Insert Data Booklet INSTRUCTIONS • Section A: answer all questions. • Section B: answer two questions. • Use a black or dark blue pen. You may use an HB pencil for any diagrams or graphs. • Write your name, class and index number in the boxes at the top of the page. • Write your answer to each question in the space provided. • Do not use an erasable pen. Do not use correction fluid or tape. • You may use an approved calculator. INFORMATION • The total mark for this paper is 100. • The number of marks for each question or part question is shown in brackets [ ]. • The insert contains information for Question 1. This document has 40 pages. Any blank pages are indicated. Question Marks Section A (answer all) 1 / 18 2 / 23 3 / 19 Section B (answer two) 4 / 20 5 / 20 6 / 20 Total / 100 H3
2 © Raffles Institution 2026 9813/01/S/26 Section A Answer all questions in this section in the spaces provided. 1 The information provided in the insert is taken from a published scientific article. Other published articles may not agree with all of this information. You should read the whole insert before you start to answer any questions and use the information it contains to answer the questions. (a) (i) Explain why GDL-based reactors achieve higher current densities than H-type cells at the same applied cell potential. ……………………………………………………………………………………………….. ……………………………………………………………………………………………….. ……………………………………………………………………………………………. [1] (ii) When flooding in a GDL-based reactor occurs, an increase in applied cell potential is required to maintain the same current density for CO2 reduction. Explain why. ……………………………………………………………………………………………….. ……………………………………………………………………………………………….. ……………………………………………………………………………………………….. ……………………………………………………………………………………………. [1] (iii) Using Figure 1.1, suggest why Mode II is more effective than Mode I in reducing the concentration of H2O at the catalyst surface. ……………………………………………………………………………………………….. ……………………………………………………………………………………………….. ……………………………………………………………………………………………. [1] (iv) With reference to the structure of Nafion in Figure 1.2, explain why the Nafion/Cu catalyst GDL exhibits the lowest selectivity for C2+ products. ……………………………………………………………………………………………….. ……………………………………………………………………………………………….. ……………………………………………………………………………………………….. ……………………………………………………………………………………………. [1]
3 © Raffles Institution 2026 9813/01/S/26 [Turn over (b) The electrochemical reduction of CO2 to C2H4 is represented by equation 1. equation 1 2CO2(g) + 12H+(aq) + 12e– ⇌ C2H4(g) + 4H2O(l) (i) Assuming that ECO2/C2H4 is +0.09 V , calculate the equilibrium cell potential, EC2H4, for the reduction of CO2 to C2H4. Hence, calculate the standard Gibbs’ free energy change, ΔG, for the reduction of CO2 to C2H4 and comment on its thermodynamic feasibility. …………………………………………………………………………………………… [2] The PT/Cu catalyst GDL was used in the reduction of CO2 to C2H4 at a total current density of 2 A cm–2. (ii) Calculate the applied cell potential required to obtain the maximum FC2H4 and CC2H4. You may assume that the maximum FC2H4 and CC2H4 can be approximated to the maximum FC2+ and CC2+ respectively. [1] (iii) Given that the area of the electrode is 1.0 cm 2, calculate the rate of formation of C2H4, in mol s–1, in the PT/Cu catalyst GDL in (b)(ii). [2]
4 © Raffles Institution 2026 9813/01/S/26 (iv) Hence, calculate the concentration of C2H4, in ppm, in the outlet gas. You may assume that the reaction was carried out at room temperature and pressure. If you were unable to calculate a value for the rate of formation of C 2H4 in (b)(iii), you should use 1.00 10–6 mol s−1. This is not the correct answer. [2] (v) Predict the effect (if any) of increasing the gas flow rate on the rate of formation of C2H4. ……………………………………………………………………………………………….. ……………………………………………………………………………………………….. ……………………………………………………………………………………………. [1] (vi) CO is an intermediate formed during the reduction of CO2 to C2+ products. Given that Ag catalyst has weaker CO adsorption strength than Cu catalyst, suggest how changing the catalyst from Cu to Ag will affect the yield of C2+ products. ……………………………………………………………………………………………….. ……………………………………………………………………………………………….. ……………………………………………………………………………………………. [1] (vii) Suggest why C2+ products are more desirable as fuels than CO. ……………………………………………………………………………………………….. ……………………………………………………………………………………………. [1]
5 © Raffles Institution 2026 9813/01/S/26 [Turn over (c) (i) Explain why FC2+ decreases when the partial pressure of CO2 is halved. ……………………………………………………………………………………………….. ……………………………………………………………………………………………….. ……………………………………………………………………………………………. [1] (ii) Using equation 2, calculate the change in electrode potential, ΔE, when only the partial pressure of CO2 is halved. equation 2 E = E – (0.0592n ) log PC2H4PCO22 [H+]12 [1] (d) Explain why achieving both high current density (jC2+) and high Faradaic efficiency (FC2+) is important for electrocatalytic reduction of CO2. ……………………………………………………………………………………………………….. ……………………………………………………………………………………………………….. ……………………………………………………………………………………………………….. ……………………………………………………………………………………………………. [2] [Total: 18]
6 © Raffles Institution 2026 9813/01/S/26 2 (a) The reaction between D with E in a dry solvent produces F as the major product. F, C40H30N4O8, is a widely used ligand in transition metal complexes. (i) State the type of reaction that occurs between D and E. ……………………………………………………………………………………………. [1] (ii) Assign the stereochemistry (E or Z) at each of the C=N bond in F. Explain your reasoning. ……………………………………………………………………………………………….. ……………………………………………………………………………………………….. ……………………………………………………………………………………………….. ……………………………………………………………………………………………….. ……………………………………………………………………………………………. [2] (iii) The reaction between D and E can also produce other stereoisomers of F. State the total number of possible stereoisomers, including F, that can be formed from the reaction. You may assume that all carbon atoms in F are on the same plane. ……………………………………………………………………………………………. [1]
7 © Raffles Institution 2026 9813/01/S/26 [Turn over (iv) Besides steric effects, suggest one other reason to explain why the reaction favours the formation of F over the other stereoisomers. ……………………………………………………………………………………………….. ……………………………………………………………………………………………….. ……………………………………………………………………………………………. [1] UV-visible spectroscopy can be used to monitor the r
Content continues in the PDF. Download PDF
