2026 RI H3Chem Prelims Insert
Uploaded by Kozak327 · 10 November 2026
Preview
Text from the first pages1 This document has 3 printed pages. © Raffles Institution 2026 9813/INSERT/01/S/26 [Turn over RAFFLES INSTITUTION 2026 YEAR 6 PRELIMINARY EXAMINATION Higher 3 CHEMISTRY 9813/01 Paper 1 28 September 2026 INSERT 2 hours 30 minutes INFORMATION • This insert contains information for Question 1. • You may annotate this insert and use the blank spaces for planning. Do not write your answers on the insert. H3
2 © Raffles Institution 2026 9813/INSERT/01/S/26 Information for Question 1 Electrocatalytic CO 2 reduction coupled with renewable electricity has been identified as an attractive route to produce fuels and chemicals with out carbon footprint. Numerous catalysts have been developed to direct the selectivity of CO2 reduction towards valuable fuels, including carbon monoxide and multi -carbon products (C 2+) such as ethene, ethanol and propanol. However, the major obstacle to the practical implementation remains to achieve sufficient energy efficiency at high production rates. The efficiency of this process depends not only on the choice of catalyst, but also on the reaction microenvironment, which influences the availability of reactants and extent of competing reactions, such as H2O reduction. H-type cells have been extensively employed to evaluate the reaction mechanisms in CO 2 reduction. In these cells, CO2 is bubbled into the aqueous electrolyte, where it dissolves and diffuses to the cathode surface for reduction. However, the current density, defined as the amount of current flowing per unit area of the electrode, in H-type cells for CO 2 reduction is low. In contrast, gas-diffusion layer (GDL)-based reactors have higher current density, as the CO2 is directly supplied to the catalyst surface via a gas inlet . However, a key challenge is the flooding by large amounts of H2O at the catalyst surface in aqueous electrolyte. This leads to a decreased selectivity towards CO 2 reduction. Furthermore, an increase in applied cell potential is required to maintain the same current density for CO2 reduction. To reduce flooding at the catalyst surface , polymers are introduced to modify the GDL -based reactors via two modes, Mode I and Mode II. Figure 1.1 shows Mode I and Mode II that were studied. Mode I Mode II Figure 1.1 In Mode I, the polymer (large sphere) was physically mixed with the catalyst (small sphere). In Mode II, a thin and continuous polymer layer is coated on the catalyst surface and was found to be more effective in reducing the concentration of H2O at the catalyst surface. In both Modes I and II, the polymer and catalyst make up the electrode. Catalyst layer CO2 CO2 Catalyst layer aqueous electrolyte
3 © Raffles Institution 2026 9813/INSERT/01/S/26 Three polymers (PT, PCR and Nafion) were used to prepare the Cu catalyst gas-diffusion electrode in the GDL-based reactor using Mode II. The selectivity and energy efficiency for the formation of C2+ products were studied for each of these polymer/Cu catalyst GDL. Figure 1.2 The selectivity for the formation of C2+ products is represented by its Faradaic efficiency (FC2+) as shown in equation 1.1. equation 1.1 FC2+ = jC2+ jtotal jC2+ is the current density for the formation of C2+ products and jtotal is the total current density. The cathodic energy efficiency (CC2+) for C2+ products is represented by equation 1.2. It shows how efficiently the electrical energy supplied is converted into chemical energy in C2+ products. equation 1.2 CC2+ = |EC2+| E (FC2+) = | ECO2/C2+ – 1.23 | E (FC2+) where EC2+ is the equilibrium cell potential ECO2/C2+ is the electrode potential of the CO2/C2+ half-cell E is the applied cell potential The maximum FC2+ and CC2+ were studied for each of the polymer/Cu catalyst GDL. For PT/Cu catalyst GDL, a maximum FC2+ of 87% and CC2+ of 51% for C2+ products were obtained at a total current density of 2 A cm–2, showing the highest FC2+ and CC2+ compared to the other two polymer/Cu catalyst GDL. The inlet and outlet gas flow rates were both set at 25 cm3 min–1. ________________________________________________________________ Copyright Acknowledgements: Question 1 © Chen et al. (2024) Nature Communications, 15, 5893
Content continues in the PDF. Download PDF
